Boards & Programmer
Showing 31–45 of 108 resultsSorted by latest
-
Development Board
Digispark ATTINY85 Mini USB Development Board
Although small in size, great in capabilities. The Digispark ATTINY85 Mini USB Development Board is similar to the Arduino but cheaper and smaller (of course a bit less powerful). With a whole host of shields to extend its functionality and the ability to use the familiar Arduino IDE, this board is a great way to jump into microcontroller electronics.
Complete USB Development Board Cheap Enough to Leave in a Project. If you have never heard of the Digispark ATtiny board before, it may take you more than a moment to understand its full power and potential. So read this carefully:
Firstly, its a 20MHz, AVR 8-bit microcontroller with 8 KB flash, 512 bytes of RAM
You get up to 5 GPIOs, 4 ADCs, 2 PWMs, 1 SPI, and 1 I2C[*]
Secondly, its fully compatible with Arduino
Thirdly, it can be directly programmed via USB without needing any other programmer!
And finally, it is available at a cheap price!!
The Digispark is shipped fully assembled except for the two included and easy to solder headers.
SKU: n/a -
Arduino, Modules
8 Channel 5V Relay Module with Optocoupler
It is an 8 Channel Isolated 5V 10A Relay Module, which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, PLC, etc. It is also able to control various appliances and other types of equipment with large current. Relay output maximum contact is AC250V 10A and DC 5V 10A. One can connect a microcontroller with standard interface directly to it. Red working status indicator lights are conducive to the safe use. It has a wide range of applications such as all MCU control, industrial sector, PLC control, smart home control.
So, ready to get switching on your Raspberry Pi?! This neat relay module features 8 x 5V relays rated at 10A/250V each. t is designed to switch up to 4 high current (10A) or high voltage (250V) loads with the help of microcontroller!
Each relay can individually switch to on/off state. It only requires a voltage of approx 1.0V to switch the inputs on but can handle input voltages up to 5V. This makes it ideal for 3.3V & 5V devices.
SKU: n/a -
Arduino, Modules
4 Channel 5V Relay Module with Optocoupler
It is 4 Channel Isolated 5V 10A Relay Module, A wide range of microcontrollers such as Arduino, AVR, PIC, ARM and so on can control it.
It is also able to control various appliances and other types of equipment with large current.
Relay output maximum contact is AC250V 10A and DC5V 10A. One can connect a microcontroller with standard interface directly to it.
Red working status indicator lights are conducive to the safe use. It has a wide range of applications such as all MCU control, industrial sector, PLC control, smart home control.
Ready to get switching on your Raspberry Pi?! This neat relay module features 4 x 5V relays rated at 10A/250V each. It is designed to switch up to 4 high current (10A) or high voltage (250V) loads with the help of microcontroller!
Each relay can individually switch on/off by an opto-isolated digital input, which that can connect directly to a microcontroller output pin. It only requires a voltage of approx 1.0V to switch the inputs on but can handle input voltages up to 5V. This makes it ideal for 1.0V to 5V devices.
SKU: n/a -
Arduino, Modules
37 In 1 Sensor Module Kit for Arduino
This 37 In 1 Sensor Module Kit for Arduino is supplied with a variety of sensors that are compatible with Arduino Boards. This is the most complete performance starter kit with all the essential Arduino sensors.
It comprises 37 Pcs essential Arduino components. The kit includes the latest Arduino components that can be used to turn your idea into a real product.
Tons of updated lessons and Arduino codes are available on Google and Youtube for free. It is extremely easy for Arduino fancier to control and use these modules. This kit will help you control the physical world with sensors.
SKU: n/a -
Arduino, Modules
360 Degree Rotary Encoder Module
A 360 Degree Rotary Encoder is a Bread Board Friendly extremely precise module that provides an indication of how much the knob has been rotated AND what direction it is rotating in. It is an incremental electro-mechanical device that converts the angular position or motion of a shaft or axle to digital code. The output of incremental encoders provides information about the motion of the shaft, which is typically further processed in processor / controllers into information such as speed, distance, and position.
It’s a great device for stepper and servo motor control. You could also use it to control devices like digital potentiometers.
SKU: n/a -
Arduino, Modules
3/4 inch Water Flow Sensor – YF-S403
3/4 inch Water flow sensor YF-S403 is mainly consists of plastic valve body, rotor assembly and hall current sensor. This flow sensor can be used for accurate flow measurement. It is installed in the hot water inlet end for detecting water flow. When water through the flow rotor assembly, magnetic rotor will rotate and Speed will change as the flow change. Hall current sensor output corresponding pulse signal and feedback to controller, then the controller will control the flow. Can be used for water heaters, credit card machines, water vending machine, flow measurement device.
SKU: n/a -
Arduino, Modules
3/4 inch Brass Water Flow Sensor – SEN-HZ43WB
Now easily measure water (liquid) flow in your application using this 3/4″ Brass water flow sensor. This is good quality flow sensor with brass body and can be used for industrial and commercial applications. This three forth inch water flow sensor is used extensively is various types of vending machines.
This water flow sensor is connected in line with the liquid whose flow rate has to be measured. There is a simple rotating wheel with a magnet and when the liquid flows the wheel is rotated and a hall effect sensor measures how many times he wheel is rotated and accordingly gives pulses. By counting the number of pulses you can easily calculate the flow rate as well as the amount of liquid dispensed.
SKU: n/a -
Arduino, Modules
2 Channel 5V Relay Module with Optocoupler
This is a 5V, 10A 2-Channel Relay interface board. It can be used to control various appliances, and other equipments with large current. It can be controlled directly with 3.3V or 5V logic signals from a microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic).
It has a 1×4 (2.54mm pitch) pin header for connecting power (5V and 0V), and for controlling the 2 relays.
SKU: n/a -
Arduino, Modules
16 Channel 5V Relay Module with Optocoupler
This is a 16 Channel 5V Relay Module with Optocoupler, Be able to control various appliances and other equipment with a large current. It can be controlled directly by Micro-controller (Arduino, 8051, AVR, PIC, DSP, ARM, MSP430, TTL logic).This is 5V 16-Channel Relay interface board and each one of the individual relays needs 15-20mA Driver Current. The board features indication LED for Relay output status and the standard interface that can be controlled directly by many of widely used microcontrollers like Arduino etc.The 5V electromechanical relay module with AC contact capacity of 250V which also include light coupling protection(optocoupler) for isolation of control circuitry. The plate load power module doesn’t need an external power supply. It supports all SCM Drive.SKU: n/a -
Arduino, Modules
1/8 inch Water Flow Sensor – YF-S401
1/8 inch Water flow sensor YF-S401 consists of a plastic valve body, a water rotor, and a hall effect sensor – when water flows through, the internal rotator will change its speed with different rate of flow and hall effect sensor outputs the corresponding pulse signal. Use with laser cutters or CNC to measure if and how much water is flowing through laser tube or CNC spindle for cooling.
SKU: n/a -
Arduino, Modules
1/4 inch Water Flow Sensor – YF-S402
This 1/4 inch water flow sensor is basically a small turbine whose output signal is a series of digital pulses. The frequency of the pulses is proportional to the flow rate of the liquid passing through the sensor. That digital signal, whose frequency is in the range between 0Hz and 100Hz, can be read directly through one of the digital input/output pins of a microcontroller.
SKU: n/a
