The USB ASP AVR Programming Device for ATMEL processors is a USB in-circuit programmer for Atmel AVR controllers. USB ASP AVR Programming Device for ATMEL Processors simply consists of an ATMega88 or an ATMega8 and a couple of passive components. The programmer uses a firmware-only USB driver; no special USB controller is needed.
| Model no | USBASP AVR Programmer |
| Length (mm) | 63.3 |
| Width (mm) | 20.5 |
| Height (mm) | 10.5 |
| Weight (gm) | 15 |
ULINK2 Keil Debug Adapter connects user PC’s USB port to your target system (via JTAG, SWD, or OCDS) and allows you to program and debug embedded programs on target hardware. ULINK2 can be used for on-chip debugging (using on-chip JTAG, SWD, or SWV) and flash memory programming (using user-configurable flash programming algorithms).
Using the ULINK2 adapter together with the Keil µ Vision IDE/Debugger, users can easily create, download, and test embedded applications on target hardware.
By using ULINK2, you can examine memory and registers, single-step through programs then insert multiple breakpoints, run programs in real-time and program Flash Memory.
Breakpoints RAM: Unlimited ROM Breakpoints (ARM7 / 9): 2 max ROM Breakpoints (Cortex-M3): 6 max Execution breakpoints (Set While Executing): yes Access Breakpoints (ARM7 / 9): 2 max (R / W Only, With Value) Access Breakpoints (Cortex-M3): 4 max (With Value) Trace History: no Real-Time Agent: yes JTAG clock : <= 10MHz JTAG RTCK support (Return Clock): yes Memory R / W (Bytes / sec): 28K Flash R / W (Bytes / sec): 25K Single-Step (Fast) (Instructions / sec): 50 SUPPORTED DEVICES: Actel (ARM7/ARM9/Cortex Family) COREMP7, Cortex-M1
This is an SPI BIOS FLASH Non-Dismantling Test Program IC programming clip that is perfect for reading or writing EEPROMs. This clip allows for in-circuit programming of SOP8 chips.
Now you can program SOP8 chips without having to remove them from the circuit board, just clip to the chip and use one of the two breakout adapter boards to connect to your programmer.
The ISP cable is wired 1:1 so will support any programmer that has a ZIF/DIL socket and supports ISP/ICSP Mode
ST-Link V2 Programmer For STM8 and STM32 is fully consistent with the official version, support for automatic upgrades, support the full range STM32 SWD (only 4pins including SWCLK, SWDIO, and power) and a full range STM8 SWIM (only 4pins including SWIM, Reset and power) download and debug.
Use this device to send program code to the 32-bit STM32 ARM Cortex or 8-bit STM8 microcontrollers. The header for this ST-Link v2 programmer contains connections for 5V, 3.3V, SWCLK, SWDIO, SWIM, Reset (RST/NRST) and GND. The connector on the opposite side of this device is a USB connector and is intended to be plugged into the computer.
The ST-LINK/V2 is an in-circuit debugger and programmer for the STM8 and STM32 microcontroller families. The single wire interface module (SWIM) and JTAG/serial wire debugging (SWD) interfaces are used to communicate with any STM8 or STM32 microcontroller located on an application board.
Much similar in architecture for debugging, the ST-LINK/V2 and the ST-LINK/V2-ISOL share the same features like digital isolation between the PC and the target application board this allows to withstands voltages of up to 1000 Vrms.
Specifically the debugger incorporates the use of USB full-speed interface to communicate with the ST Visual Develop (STVD) or ST Visual Program (STVP) software for STM8 application, and use of the USB full-speed interface to communicate with Atollic®, IAR™, Keil®or TASKING integrated development environments for STM32 applications.
