Features:
- Supports many different EEPROMS 150mil / 209mil 24Cxx, 25Cxx, 93Cxx, 95xxx, 25Lxx
- Pitch Lead: 2.54mm
- Pitch row: 3.81mm
- SOIC 8 / SOP8 Clip
- Spring Loaded
Programmers
SPI BIOS FLASH Non-Dismantling Test Program Clip SOP8 24C 93C 25LF
This is an SPI BIOS FLASH Non-Dismantling Test Program IC programming clip that is perfect for reading or writing EEPROMs. This clip allows for in-circuit programming of SOP8 chips.
Now you can program SOP8 chips without having to remove them from the circuit board, just clip to the chip and use one of the two breakout adapter boards to connect to your programmer.
The ISP cable is wired 1:1 so will support any programmer that has a ZIF/DIL socket and supports ISP/ICSP Mode
Related products
-
Programmers
USB ASP AVR Programmer for ATMEL Processors
The USB ASP AVR Programming Device for ATMEL processors is a USB in-circuit programmer for Atmel AVR controllers. USB ASP AVR Programming Device for ATMEL Processors simply consists of an ATMega88 or an ATMega8 and a couple of passive components. The programmer uses a firmware-only USB driver; no special USB controller is needed.
SKU: n/a -
Programmers
ST Link V2 Programmer For STM8 and STM32
ST-Link V2 Programmer For STM8 and STM32 is fully consistent with the official version, support for automatic upgrades, support the full range STM32 SWD (only 4pins including SWCLK, SWDIO, and power) and a full range STM8 SWIM (only 4pins including SWIM, Reset and power) download and debug.
Use this device to send program code to the 32-bit STM32 ARM Cortex or 8-bit STM8 microcontrollers. The header for this ST-Link v2 programmer contains connections for 5V, 3.3V, SWCLK, SWDIO, SWIM, Reset (RST/NRST) and GND. The connector on the opposite side of this device is a USB connector and is intended to be plugged into the computer.
SKU: n/a -
Programmers
PICkit3 Debugger Programmer Emulator Controller Development Board
This is PICkit3 Debugger Programmer Emulator Controller Development board w/ Pinout diagram to ease the customer. The USB connection is more stable than ICD2.
PICKIT3.5, begin to support Win7 system. Full patch design, patch through the reflow soldering processing, more stable quality. PIC developing data, C language development tool manual. A lot of PIC basic experiment program code; ICD2 PICKIT3 etc application specification.
The MPLAB PICkit 3 allows debugging and programming of PIC and dsPIC Flash microcontrollers at a most affordable price point using the powerful graphical user interface of the MPLAB Integrated Development Environment (IDE). The MPLAB PICkit 3 is connected to the design engineers PC using a full-speed USB interface and can connect to the target via a Microchip debug (RJ-11) connector (compatible with MPLAB ICD 2, MPLAB ICD 3 and MPLAB REAL ICE).
SKU: n/a -
Programmers
ST LINK V2 in-circuit Debugger / Programmer for STM8 and STM32
The ST-LINK/V2 is an in-circuit debugger and programmer for the STM8 and STM32 microcontroller families. The single wire interface module (SWIM) and JTAG/serial wire debugging (SWD) interfaces are used to communicate with any STM8 or STM32 microcontroller located on an application board.
Much similar in architecture for debugging, the ST-LINK/V2 and the ST-LINK/V2-ISOL share the same features like digital isolation between the PC and the target application board this allows to withstands voltages of up to 1000 Vrms.
Specifically the debugger incorporates the use of USB full-speed interface to communicate with the ST Visual Develop (STVD) or ST Visual Program (STVP) software for STM8 application, and use of the USB full-speed interface to communicate with Atollic®, IAR™, Keil®or TASKING integrated development environments for STM32 applications.
SKU: n/a
